Nortel Networks BCM200 Manual de usuario Pagina 237
- Pagina / 382
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 20 Preparing hardware for maintenance or upgrades 237
BCM200/400 4.0 Installation and Maintenance Guide
Figure 107 Install the base function tray
11 Insert all connectors in the correct locations on the base function tray face.
12 Restore the BCM system to operation. See “Restarting the system after maintenance” on page
232.
13 Observe the system status monitor LEDs to ensure the base function tray initializes correctly.
To remove the base function tray bezel
1 Shut down the system (see “Performing a system shutdown” on page 231).
2 Disconnect the BCM system from the AC power outlet.
Warning: Protect the hardware components against damage from electrostatic discharge.
Always wear a grounded wrist strap before you handle components. Always place the
components in a static-free container.
Warning: Use care when removing or inserting the base function tray. Do not forcefully
remove or insert the base function tray because you could damage or stretch the cables.
Fasten base function tray
latch screws
4
Slide base function tray partially
into the main unit
1
3
2
Connect DS30 cables to the
MSC
Insert base function tray completely. Move
base function tray latches to the locked
position
- Maintenance Guide 1
- Trademarks 2
- SOFTWARE LICENSE 3
- N0060612 4
- Task List 5
- Contents 9
- Regulatory information 17
- EMI/EMC (FCC Part 15) 18
- Important safety instructions 19
- Use of a music source 20
- Enhanced 911 configuration 21
- Radio-frequency interference 21
- 22 Regulatory information 22
- Additional safety information 23
- 24 Regulatory information 24
- Chapter 1 25
- 26 Chapter 1 Getting started 26
- Chapter 1 Getting started 27 27
- Related publications 29
- How to get help 30
- Chapter 2 31
- BCM200 main unit 32
- BCM400 main unit 34
- BCM400 advanced function tray 37
- Media services card (MSC) 41
- Main card 43
- Main card connections 44
- PCI riser card 45
- Data networking components 46
- I/O interface card 48
- MBM bays and backplane 50
- Media bay modules (MBMs) 51
- Figure 27 DTM faceplate 54
- 1Aux 2 3 4 55
- 87 6 Aux5 55
- Figure 29 BRIM faceplate 56
- Figure 30 GATM faceplate 56
- 4x16 media bay module 58
- Digital drop and insert MUX 61
- BCM400 expansion gateway 62
- BCM components 63
- BCM400 redundant power supply 64
- Uninterruptable power supply 66
- Hard disk 66
- RAID upgrade kit 67
- Cooling fan 68
- Field replaceable units (FRU) 69
- Table 17 MBM 71
- Telephones and adapters 72
- ABC DEF 73
- GHI JKL MNO 73
- PQRS TUV WXYZ 73
- Accessories 75
- Chapter 3 77
- Media bay module LEDs 79
- DTM LEDs 80
- Figure 47 DTM LEDs 81
- Table 21 DTM LED functions 81
- BRIM LEDs 82
- Chapter 4 83
- Chapter 5 87
- Electrical requirements 88
- Analog loop 89
- Basic hardware 89
- Optional equipment 89
- Other hardware and tools 90
- Chapter 6 91
- Unpacking the main unit 92
- Install rack-mount 93
- Figure 55, or Figure 56) 94
- N0060612N0060612 100
- Chapter 7 101
- Unpacking the expansion unit 102
- Installing the expansion unit 102
- Figure 60 DS256 cable 103
- Table 24 DS256 cable pinout 103
- (see Figure 61) 104
- Chapter 8 105
- Selecting trunk MBMs 106
- To select trunk MBMs 106
- Selecting station MBMs 108
- To select station MBMs 108
- Determining system capacity 109
- Setting offsets 110
- Determining bus requirements 111
- Single-density modules 112
- Double-density modules 112
- To determine bus requirements 113
- Assigning DS30 resources 114
- 3/5 bus split 115
- Setting MBM DIP switches 120
- DTM switch settings 121
- DDIM switch settings 122
- BRI switch settings 123
- CTM switch settings 123
- CTMs and CTM8s 124
- GATM switch settings 125
- 4x16 switch settings 126
- (DNs) for each DS30 bus 127
- Table 39 ASM 8 settings 128
- DSM switch settings 130
- FEM switch settings 133
- BCM400 expansion gateway MBMs 134
- Installing an MBM 135
- Chapter 9 137
- To connect power and wiring 138
- Wiring the MBMs 140
- 1 2 3 4 5 6 7 8 142
- 6 5 4 3 2 1 142
- To connect the GATM 143
- Table 48 DSM wiring chart 146
- Table 49 ASM wiring chart 147
- Wiring the FEM 148
- To connect the fiber cables 148
- Setting DNs and port numbers 149
- MBM combinations 150
- Fully-loaded setup 151
- DECT combinations 153
- Changing configurations 154
- System setup 155
- Connecting the cards 156
- To connect the modem 157
- Table 59 V.35 adapter cable 158
- Installing the cards 159
- Chapter 10 161
- Installing IP Phones 165
- Moving telephones 166
- Chapter 11 167
- Installing the ATA2 168
- To connect the ATA2 169
- Mounting the ATA2 169
- To mount the ATA2 on a wall 170
- Configuring the ATA2 172
- Chapter 12 173
- Figure 87 Audio input jack 174
- Music-on-hold specifications 175
- Next step 176
- Chapter 13 177
- To configure your computer 179
- Null modem cable setup 180
- Software keycode 181
- Chapter 14 183
- Initial parameters overview 184
- Startup parameters overview 185
- Chapter 15 187
- To enter the keycodes 188
- To configure the IP address 188
- To configure the modem 189
- To select the region 189
- To initialize voice mail 190
- Chapter 16 193
- Prerequisites 194
- Accessing the BCM system 194
- To connect to the BCM system 195
- To enter a keycode 195
- To configure IP Phones 200
- To configure SNMP settings 201
- To create user accounts 203
- Chapter 17 205
- Startup Profile requirements 206
- Configuring basic parameters 207
- Chapter 18 211
- To configure the MBM 212
- Configuring modem settings 213
- Checking for software updates 213
- Configuring voice mail 213
- Customizing security policies 213
- Performing a backup 214
- Chapter 19 215
- System status display LEDs 216
- Monitoring the RAID LEDs 219
- To determine RAID status 220
- RAID disk mirroring 221
- To access disk mirroring 222
- Table 82 Step table 225
- BCM system does not function 226
- ATA2 does not function 227
- Chapter 20 229
- Special tools 231
- Performing a system shutdown 231
- Figure 111 241
- Remove the 245
- Slide cover open 245
- Lift cover at rear 245
- Slide cover 247
- Press cover down 247
- Install the top 247
- Chapter 21 249
- Removing an MBM 250
- Chapter 22 253
- Installing a RAID system 255
- Removing a hard disk cage 258
- Installing a hard disk cage 261
- To install a hard disk cage 262
- Chapter 23 275
- Unfasten BCM200 277
- MSC guide bracket 277
- BCM200 MSC guide bracket 277
- I/O Card 277
- Table 83 Power supply LED 282
- Remove the inner 289
- Fasten power supply 291
- Chapter 24 299
- To remove the WAN card 301
- Installing the WAN card 302
- Base function tray extension 305
- MSC mounting screws 305
- PEC III slots 305
- To remove the modem card 307
- Installing the modem card 309
- To install a modem card 309
- Figure 167 Modem port label 310
- Replacing memory 315
- To remove a DIMM card 317
- To install a DIMM card 318
- Chapter 25 323
- Removing a BCM400 cooling fan 324
- Removing a BCM200 cooling fan 329
- Power supply 333
- Troubleshooting cooling fans 334
- Appendix A 335
- Appendix B 337
- Appendix C 339
- Appendix D 343
- Appendix E 347
- Appendix F 349
- Appendix G 351
- Caller ID display formats 355
- GASM8 parameters 371
- ISDN line services 374
Relacionado con productos y manuales para Redes Nortel Networks BCM200
Redes Nortel Networks P0919439 Manual de usuario
(95 paginas)
(95 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales